You have no items in your shopping cart.

Subtotal: £0.00

IMAGE

More Views

SOUDAL FIX ALL FILLS & BONDS HAND HELD 750ml PU ADHESIVE EXPANDING FOAM INSULATION PANEL

Be the first to review this product

Availability: In stock

£8.00

Details

Fix All Fills & Bonds Handheld is a ready to use single component self-expanding polyurethane adhesive. The product has been developed for clean, efficient, economic and permanent bonding of insulation panels and lightweight decorative elements in wall and roof areas.

 

Characteristics

 

·        Saving of up to 30% in working time.

·        Very good initial bond, even at low temperatures.

·        Economic in use due to precise application – sufficient for 12m² of insulation panels (3 beads per m²).

·        Suitable for vertical and horizontal applications.

·        Can be applied at temperatures as low as -5°C (temperature of aerosol can needs to be at least +5°C).

·        Excellent insulation characteristics, enhances performance of insulation panels when filling gaps (ca 0,036 W/(m∙K).

·        Remains flexible, does not become brittle.

·        Suitable for uneven surfaces as it fills cavities.

·        Limited post expansion, resulting in fast and precise installation of insulation panels

·        Very wide adhesion spectrum: various types of boards such as plasterboard and dry lining, roofing, concrete, stone, brick, timber, various insulation panels and decorative elements based on PU, Polystyrene, Phenol resin foam, etc.

·        Compared to usual types of PU Roof adhesives and Dry lining or plasterboard adhesives, huge savings in space and weight.

·        Fast curing: 1 hour after application work can continue on flat roofs or boards can be plastered.

·        Free of solvents.

·        Compatible with most types of paints, many solvents and chemical substrates.

·        Does not age or rot, but should not be exposed to UV radiation (cover with paint or plaster if necessary).

 

Applications

 

·        Bonding of various types of insulation panels onto roofs, walls and façades.

·        Bonding of decorative elements in façade applications.

·        Filling of cavities between insulation panels.

 

Packaging

 

Colour: light orange

Packaging: aerosol can, 750mL content.

 

Shelf life and Storage

 

·        12 months in unopened packaging in a cool and dry storage place at temperatures between +5°C and +25°.

·        Always store aerosol can with the valve pointed upwards.

·        Partially used aerosol cans must be sealed well, valves cleaned and used within a short time.

 

Surfaces

 

Type: all types of panels, boards, dry lining, roofing, timber, concrete, metals, fiber cement, etc

State of Surface: clean, free of dust and grease

We recommend a compatibility test to ensure optimal performance.

 

Application Method – Roof elements

 

·        Prior to application, protect and cover adjacent surfaces.

·        During strong winds, ensure that no adjacent areas are exposed.

·        Thread the straw tightly to the can.

·        Shake at least 30 times with the can upside down to ensure proper mixing of the ingredients and maximum yield.

·        Repeat shaking after work intervals.

·        Applying 30mm beads is easy with the MEGA ADAPTER STRAW.

·        Apply directly onto the surface, holding the mega adapter straw at an angle of about 90° to the surface and ensure a distance of about 1 to 2 cm between nozzle and surface. The nozzle should not be in direct contact with the surface.

·        Apply at least 3 beads per m². At the edges of the insulation panels, at corners and where there is increased wind exposure, the quantity of adhesive should be increased (see DIN 1055, part 4).

·        Wait for 4-5 of minutes and then press insulation panels into the adhesive and hold in place for approx 1min. (within 8 minutes from extrusion, 20°C, 65% r.h.). At higher temperatures/humidity, the open time will be reduced; at lower temperatures/humidity, the open time will be longer.

·        Fill all open joints with Fix All Fills & Bonds.

·        Leave to cure for at least 2 hours before submitting the bond to pressure (walking, etc.)

·        Remove surplus adhesive with a cutter knife after full cure.

·        Ready to plaster in 1 hour.

 

Application Method – Lightweight Dry Lining / Boards

 

·        Prior to application, protect and cover adjacent surfaces.

·        Screw the mega adapter straw tightly to the thread of the can.

·        Shake at least 30 times with the can upside down to ensure proper mixing of the ingredients and maximum yield.

·        Repeat shaking after work intervals.

·        Apply directly onto the surface, holding the mega adapter straw at an angle of about 90° to the surface and ensure a distance of about 1 to 2 cm between nozzle and surface. The nozzle should not be in direct contact with the surface.

·        Apply adhesive onto boards in a continuous 30mm bead around the perimeter at about 3 cm distance from the edge.

·        Inside this bead apply adhesive in a zigzag bead, ensuring that at least 1/3 of the surface is covered when panel is pressed against the wall.

 

·        Wait for a couple of minutes and then press boards strongly onto substrate (within 8 minutes from extrusion, 20°C, 65% r.h.). At higher temperatures/humidity, the open time will be reduced; at lower temperatures/humidity, the open time will be longer.

·        To improve spreading of the foam and obtain a more uniform, flatter distribution across the panel, the board can be removed and left for about 30 seconds before being pressed strongly back against the surface.

·        Remove surplus adhesive with a cutter knife after full cure.

 

Application Temperature:

Surfaces: from -5°C to +35°C

Aerosol can: from +5°C to +25°C (ideally between +15°C and +25°C)

If required acclimatize aerosol can slowly in cool or lukewarm water.

 

Clean with:

If not yet cured, use PU Foam Cleaner. Once cured, use PU Remover or remove mechanically

 

Repair with:

Fix All Fills & Bonds Hand Held

 

Health- and Safety Recommendation

 

Apply the usual industrial hygiene.

Wear gloves and safety goggles.

Remove cured adhesive mechanically only or with PU remover, never burn off.

Additional Information

COLOUR COLOUR

Customer Reviews

Write Your Own Review

You're reviewing: SOUDAL FIX ALL FILLS & BONDS HAND HELD 750ml PU ADHESIVE EXPANDING FOAM INSULATION PANEL

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Brands

  • brand
  • brand
  • brand
  • brand
  • brand
  • brand